interference fit

The washer shall be clinched to the stud end with a tight slip fit to an interference fit.

由滑动配合的相互作用力使垫片咬紧于螺栓。

互联网摘选

Stresses analysis on the interface of interference fit with boundary element method

用边界元法分析干涉配合结合面的应力分布

互联网摘选

Analysis and Improvement of Interference Fit Reliability of Thin-walled Bearing Shell

薄壁轴瓦过盈配合可靠性分析及改进

互联网摘选

The study of the assembly stresses over and above field of the lame problem for interference fit construction

非拉梅问题的过盈配合结构装配应力的研究

互联网摘选

Before the assembly of parts of the match, especially interference fit the size and the relevant review.

装配前应对吾爱内用抗菌乳膏零、器件的首要配合尺寸，特别是过盈配合尺寸及相关精度进行复查。

互联网摘选

Contraction of the outer ring due to interference fit in the housing.

收缩,外环由于干扰适合的住房.

互联网摘选

It was found by calculation that thrust load has an evident effect on contact angle while radial load influence feebly, clearance has a great impact on load distribution and appropriate interference fit increases carrying capacity, but the maximum needle burthen also increases.

计算结果表明，角接触球轴承的轴向载荷对工作接触角影响明显，而径向载荷影响很小；游隙对滚针轴承载荷分布的影响很大，适当过盈可提高承载力，但滚针最大负荷增大。

互联网摘选

Three quenched bushes are pressed on the hollow spindle ( sleeve) with a big interference fit, thus the spindle can move forward and backward precisely within the bush.

三个大干涉配合的淬火衬套压装在空心轴（镗套）上，因此，主轴能在衬套内前后精确移动；

互联网摘选

But the interference fit by hydro form result in the damage occurring on the contact surface.

然而,由于锥套与辊颈利用液压胀形实现过盈装配,使得接触面间在装配过程中发生表面损伤.

互联网摘选

Interference fit is an economical and effective method for prolonging fatigue life of jointing structures.

干涉配合是提高连接结构抗疲劳破坏能力的经济而有效的措施.

互联网摘选

Clutch engagement speed test Calculation of the Interference Fit Joints at High Rotary Speed

离合器接合转速试验高速旋转状态下压配合联接的设计计算

互联网摘选

The study showed that the structural dimensions played an important role the crankshaft gear stress. Based on these, on analyze the impact law of the structural dimensions affect to the interference fit was mainly focused.

研究表明结构尺寸对曲轴齿轮应力影响较大，在此基础上着重分析了结构尺寸对过盈量的影响规律。

互联网摘选

Study on the Performance of Interference Fit for the High Speed Spindle

高速主轴过盈联结特性研究

互联网摘选

This paper describes the application of projected tolerance zone, mainly in threaded parts and parts with interference fit to control the tole ranee in position or symmetry so that the function and assembling of these parts be ensured.

本文论述了延伸公差带的应用，主要用于螺纹件及压配合零件的连接，控制位置度和对称度的公差，以保证零件的功能要求和顺利装配。

互联网摘选

The relation between the related structural dimensions of interference fit, the contact state, the running state and the crankshaft gear stress was mainly investigated.

重点探讨了过盈联接相关结构尺寸、接触状态以及运转状态等因素与曲轴齿轮应力的关系。

互联网摘选

Such optimization results can provide a theoretical basis for selecting the rational interference fit precision.

分析结果可为选择链节合理的过盈配合精度提供理论依据.

互联网摘选

Wheelset is a key moving component on the bogie frame in locomotive and vehicle, which combines two wheels with an axle together firmly at the mode of keyless and interference fit.

轮对是列车走行部件的基础，是转向架部件的关键件，其生产方式是用轮对组装设备将车轮与车轴进行过盈无键组装配合，使之牢固结合在一起。

互联网摘选

Radial interference fit ( 0.1 mm)-336 MPa axile tensile load.

径向过盈配合0.1mm，轴向拉伸载荷336MPa。

互联网摘选

Reliability Design of the Interference Fit System of Roller Shaft

磨辊轴过盈联接系统可靠性设计

互联网摘选

Choice Selecting Interference Fit with computer

应用微机选择过盈配合

互联网摘选

For a high speed motorized spindle, the interference fit between the shaft and bearing has a great influence on the stiffness, rotary accuracy and life of the spindle.

高速电主轴轴承与转轴配合的过盈量大小对主轴的刚度、旋转精度和使用寿命具有十分重要的影响。

互联网摘选

Shrinkage fit is a way to realize the tight joint through the interference between enveloping parts ( hole) and enveloped parts ( shaft).

过盈联接是以包容件（孔）和被包容件（轴）配合后的过盈值来达到紧固联接为目的。

互联网摘选

Fatigue life increment of interference fit tapered shank bolt connections under random loading

随机载荷作用下锥形螺栓干涉配合的疲劳寿命增益

互联网摘选

Reliability design of interference fit Plastic Filter Plate for Press Filter

压配合联接的可靠性设计压滤机塑料滤板

互联网摘选